9CC-EXT35
Hot
EXT35 web

EXT35 All systems cleaner

  • All Systems Cleaner (250ml)
  • Holland Engineering
  • Made in EU / Bologna Italy
  • With EP Lubricants
  • Functions:
    • Injection Cleaning
    • Water Elimination
    • Antifreeze Protection
    • Engine Oil Line Cleaning
    • Cleaning Gearbox (Manual Transmission), ABS & Power Steering
    • Cleaning Automatic Transmission
    • Cleaning The Oil In The Cooling System
    • Cleaning Catalytic Converter / DPF
  • NOTE: The EXT35 should not be used on carburetor engines or old diesel engines with a sole mechanical pump without lift/transfer pump.

* Not available for North America

  • Dimensions
  • Instructions
  • Downloads
  • Video
Packing Can
Packaging 24 cans/carton
N.W 0.30 kg/can
7.20 kg/can
G.W. 7.60 kg/carton
Size 20 x 5.3 x 5.3 cm/can
Size 32.3 x 21.5 x 27 cm/carton

 

  1. Injection Cleaning
    For Gasoline Engine (MPI / GDI):
    First Treatment: Add the contents of one can of the EXT35 cleaner to minimum 5 liters of gasoline already contained in the fuel tank. Drive the vehicle as usual.
    Next Treatments: Once every 5,000 km add the contents of one can of EXT35 cleaner to minimum 5 liters of gasoline already contained in the fuel tank.
    For Diesel Engine (CRDI):
    First Treatment: Add the contents of one can of the EXT35 cleaner to minimum 5 liters of diesel already contained in the fuel tank. Drive the vehicle as usual.
    Next Treatments: Once every 5,000 km add the contents of one can of EXT35 cleaner to minimum 5 liters of diesel already contained in the fuel tank.
    For LPG / Gasoline Engine:
    At each service inject with the “LPG PUMP” 75ml of the EXT35 cleaner into the lpg-gas tank and pour the rest into the petrol fuel tank.
    For NCG / Gasoline Engine:
    At each 6,000 km. inject with the “GAS FLEBO” 2 doses of the EXT35 treatment into the injection rail.
  2. Lubrication Cleaning
    At each service add the contents of two EXT35 to 4 – 6 Kg. of the old oil of the engine. In case of any doubt or in case of notable deposits of black sludge it is sufficient to dilute those by doubling or tripling the dose of EXT35. In normal cases it is sufficient to run the engine at idle for about 10 minutes, but the longer the better and in the worse cases run it about 30 minutes. In order to clean the hydraulic valve lifters run the engine during the cleaning cycle also some short times above 1000 rpms. Then replace oil and filter.
  3. Cleaning Gearbox (Manual transmission), ABS & Power Steering
    Add the contents of one can of EXT35 to 4-6 kg. of the old oil of the system to be cleaned. Drive the vehicle for about 10 minutes. Replace oil and filter.
  4. Cleaning Automatic Transmission
    Add the contents of one can of EXT35 to the old oil of the automatic transmission. Drive the vehicle for about 10 minutes, using the transmission in all of its gears. Replace oil and filter.
    The traces of the EXT35 cleaner remaining in the transmission are compatible with the seals of the system and will make about only 1% of the total of the oil and therefore will not alter its viscosity.
  5. Cleaning The Oil Inside The Cooling System
    It eliminates oil and greases from the cooling system. After repairing the cooling system leakage, fill the cooling system with clean water and run the engine up to operating temperature. Add the contents of one can of EXT35 to the water. Run the engine at higher revolutions for MAXIMUM 10 minutes. Drain and clean with water. Repeat if necessary.
  6. Cleaning FAP/DPF Filter & CAT
    Eliminates soot from blocked DPF filters and catalytic converters.
    Dismount the filter.

    1. Tap the bottom.
    2. Take an empty 1.5 liter water bottle.
    3. Pour the contents of one can of EXT35 into the bottle.
    4. Fill-up with tap water. Shake and pour the mixture into the filter.
    5. Shake the filter and allow the EXT35 at least 30 minutes time (the longer the better) to soften and dissolve the deposits.
    6. Shake and empty the filter in the old oil container.
    7. Prepare another cleaning mixture and repeat the cleaning procedure.
    8. Rinse the filter with clean water.
    9. The filter or converter will result completely blank.